How to Order
01 PIZN10E 06 Z B1
High frequency AC nozzle type
Nozzle type
Symbol Type
01
Energy saving static neutralization nozzle
02
High flow rate nozzle
11
Female threads for piping
*
1
*1 Refer to the cautions when using the female threads for
piping shown below.
Input/Output specifications
Symbol Type
Nil
NPN input/output
P
PNP input/output
Power supply cable
Symbol Type Part no.
Nil
With power supply cable (3 m) IZN10E-CP
Z
With power supply cable (10 m) IZN10E-CPZ
N
Without power supply cable —
*
Mounting is interchangeable with the current model (IZN10).
Port size (One-touch fitting)
Symbol Type
06
ø6: Metric size
17
ø6.35 (1/4"): Inch size (Elbow)
Bracket
Symbol Type Part no.
Nil
None —
B1
L-bracket IZN10-B1
B2
Pivoting bracket IZN10-B2
B3
DIN rail mounting bracket IZN10-B3
*
Refer to page 12. Brackets are the same as those for the
current model (IZN10). Mounting is interchangeable.
Cautions when using the IZN10E-11mmm-m female threads for piping
Sectional view of the female threads for piping
· For the female thread (Rc1/8) type, a custom made nozzle or fittings/tubing
combination must be prepared and connected by the user.
·
If a nozzle with discharge port diameter or tubing with an I.D. of less than 4 mm is
connected, the air pressure inside the nozzle may increase depending on the configuration.
·
This product uses a high frequency AC voltage. If the air pressure around the emitter
increases during ion generation, the ion generation efficiency decreases and the maintenance
alarm (signal output, maintenance LED) will be activated (refer to the figure to the right).
·
When the maintenance alarm is generated, the static neutralization performance is decreased.
· The table below shows the supply pressure specifications when made-to-order
nozzles and fittings/tubing combinations are connected.
· When using piping materials prepared by the user, secure an air passage of 4 mm or more inside diameter. If using tubing, ensure the minimum bending radius is
used and keep the tube length to 500 mm or less.
· Please install so as not to receive a moment force on the nozzle (page 25).
Made-to-order nozzle product names/Piping examples Made-to-order nozzle part no. (page 23) Supply pressure specifications
Circular diffusion nozzle IZN10-G-X198 0.05 to 0.1 MPa
Flat diffusion nozzle IZN10-G-X199 0.05 to 0.1 MPa
Bar nozzle (straight type) IZN10-G-m-X216 0.05 to 0.1 MPa
Circumferential jet bar nozzle (straight type) IZN10-G-X278 0.05 to 0.15 MPa
Bender tube nozzle IZN10-G-m-X205 0.05 to 0.15 MPa
Long nozzle IZN10-G-m-X226 0.05 to 0.15 MPa
Fitting (Applicable tubing O.D. 6 mm) + Tube (O.D. 6 mm, I.D. 4 mm)
*
1
— 0.05 to 0.1 MPa
Fitting (Applicable tubing O.D. 8 mm) + Tube (O.D. 8 mm, I.D. 5 mm)
*
1
— 0.05 to 0.3 MPa
*1 When connecting the tubing, use a length of tubing 500 mm or less for the connection, regardless of the inside diameter size.
Nozzle Type Ionizer
IZN10E Series
Energy saving
static
neutralization
nozzle
High flow
rate nozzle
Female threads
for piping
Made to Order
(For details, refer to page 21.)
Symbol Specifications
-X367
Nozzle with right angles
®
10
